Online PEU Courses by American Trade School
Flexible courses with your schedule in mind.
With 24 approved St. Louis County Mechanical PEU courses, earning hours has never been easier. Offering both Trade and Core PEU courses, American Trade School is your one-stop shop.
Create an account.
Purchase the course or bundle that interests you.
Complete the course.
American Trade School will submit your hours to St. Louis County the Friday after your completion date.
You must have an Accela account registered with Saint Louis County for the hours to post upon submission.
The PEU bundles compile multiple individual courses into a packaged discount.
G2Ind, Trade Course, 4-PEU
The 4-PEU Refrigeration Cycle Bundle course includes all content from RC1: Compressors, RC2: Expansion Devices, RC3: Condensers, and RC4: Evaporators.
$230
G2Ind, Trade Course, 4-PEU
The 4-PEU Gas Heat Bundle includes all content from GH1: Introduction to Gas Heat, GH2: Gas Heat Components & Ignition Systems, GH3: High-Efficiency Furnaces, and GH4: Wiring Diagrams, Troubleshooting, and PMCS.
$230
G2Ind, Trade Course, 4-PEU
The 4-PEU Electric Motors Bundle course includes all content from EM1: Single-Phase Motors Fundamentals, EM2: 3-Phase and Multi-Speed Motors, EM3: Motor Applications And Motor Controls, and EM4: Electric Motor Troubleshooting.
$230
G2Ind, Trade Course, 3-PEU
The 3-PEU Electric Heat Bundle course includes all content from EH1: Introduction to Electric Heat, EH2: Electric Heat Controls, and EH3: Electric Heat Diagrams and Service Calls.
$180
G2Ind, Trade Course, 2-PEU
The 2-PEU Special Refrigeration Bundle course includes all content from SR1: Special Refrigeration Components and SR2: Special Refrigeration Defrost and Flow Control.
$125
G2Ind, Trade Course, Core Course, 2-PEU
This 2-PEU (1 Trade/1 Core) course includes all content from the IMC and IFGC Chapter 3 Courses.
$125
Each course is approved by the St. Louis County Board of Examiners for Mechanical Licensing as a Trade PEU course for HVAC Service-Installer, Sheet Metal, and Pipefitter license-holders. All courses are considered Core PEUs for Sprinklerfitters unless otherwise noted.
G2Ind, Trade Course, 1-PEU
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover Portable Electric Heating Devices, Radiant Heating Panels, Electric Baseboards, Electric Hydronic Boilers, and Central Forced-Air Electric Furnaces.
$65
G2Ind, Trade Course, 1-PEU
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover Automatic Controls for Forced-Air Electric Furnaces, Low Voltage Thermostats, Sequencers, Contactors for Controlling Electric Furnaces, and Wiring Diagrams.
$65
G2Ind, Trade Course, 1-PEU
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover Control Circuits for Forced Air Handlers, Blower Motor Circuits, Airflow in an Electric Furnace (Measurements and Calculations), Customer Relations, and Troubleshooting.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover Gas Furnaces, Gas Fuels, Gas Combustion, Gas Regulators, and Gas Valves.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover Fuel Delivery Components, Heat Exchangers, Fan & Limit Controls, Pilots, Ignition Systems, and Flame Rectification.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover High-Efficiency Furnaces, Electronic Ignition Modules & IFCs, Two-Stage Modulating Furnaces, and Venting.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover Gas Piping, Gas Furnace Wiring Diagrams & Troubleshooting Flowcharts, Spark Ignition & Intermittent Pilot Systems Troubleshooting, and Preventative Maintenance.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
The 1-PEU course will cover Electric Motor Parts, Magnetism, Speed, Start Windings, Power Supplies, Single-Phase Open Motors, Split-Phase Motors, the Centrifugal Switch, Relays, Capacitor-Start and Run Motors, and Permanent Split-Capacitor Motors.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
The 1-PEU course covers Shaded-Pole, Three-Phase Motors, Single-Phase Hermetic Motors, Potential Relays, Current Relays, PTCR, Two-Speed Compressor Motors, Three-Phase Compressor Motors, Variable-Speed Motors, Rectifiers, VFDs, ECMs, Troubleshooting.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
This 1-PEU course covers Motor Applications, Power Supply, Motor Working Conditions, Bearings, Mounting Characteristics, Drives, Motor Controls, Relays, Contactors, Starters, Motor Protection, NEC Standards, Temperature Sensing, and Overload Devices.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
This 1-PEU course covers Mechanical Motor Problems, Drive Assemblies, Belt Tension and Pulley Alignment, Electrical Problems, Open Windings, Shorted Motor Windings and Short to Ground, Starting Problems, Capacitors, Wiring, and Hermetic Motors.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU Course will cover Cooling, Heat Gain, Different Type A/C Systems, Temperature Drop, Evaporative Drainage and CFM, Compressors, Condensers, and Expansion Devices.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course covers Mechanical and Evaporator Pressure Control, Pressure Regulation, Switches and Automatic Pump-Down Systems.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course covers Controls, Types of Defrost, Refrigeration Cycle, Accessories, Receivers, Filter Driers, Check Valves and Sight Glass, Suction Line Accumulator, and Oils Separator.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover The Function and Types of Compressors, Reciprocating Compressor Components and Efficiency, Discus Valve Design, the Compressor Cylinder, and System Maintenance.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course covers Expansion Devices and Components, AXV and TXV Components, Valve Body and Diaphragm, The Needle, Seat, and Spring, The Sensing Bulb, and Algorithms and PID Controllers.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
The 1-PEU course covers Water-Cooled Condensers, Mineral Deposits, Shell-and-Coil/Tube Condensers, Wastewater Systems, Cooling Towers, Evaporative Condensers, Air-Cooled Condensers, Head Pressure Controls, Condenser Superheat, and Heat Reclaim.
$65
G2Ind, Trade Course, 1-PEU, Spire-Approved Courses
The 1-PEU course covers Temp Ranges of Refrigeration, Heat Exchange Characteristics, Removing Moisture, Types of Evaporators, Latent Heat, Superheat, Pressure Drop, Low Temp Applications, Defrosting Accumulated Moisture, and Defrost Efficiency.
$65
G2Ind, Trade Course, Core Course, Spire-Approved Courses
The 1-PEU (.5 Trade/.5 Core) course will cover codes for General and Structural Safety, Appliance Locations and Combustions Air, Installation, Access and Service Space, Condensate Drainage, Clearance Reduction, and Electrical Bonding.
$65
G2Ind, Trade Course, Core Course, Spire-Approved Courses
The 1-PEU (.5 Trade/.5 Core) 2015 IMC Chapter 3 General Regulations Course will cover codes for General Listing and Labeling, Equipment and Appliance Location, Piping Support, Access and Service Space, and Condensate Disposal.
$65
Each course is approved by the St. Louis County Board of Examiners for Mechanical Licensing as a Core PEU course for HVAC Service-Installer, Sheet Metal, Pipefitter, and Sprinklerfitter license-holders. "Comfort and Psychrometrics" is approved as a Trade PEU course for Sprinklerfitters.
G2Ind, Trade Course, Core Course, Spire-Approved Courses
The 1-PEU (.5 Trade/.5 Core) course will cover codes for General and Structural Safety, Appliance Locations and Combustions Air, Installation, Access and Service Space, Condensate Drainage, Clearance Reduction, and Electrical Bonding.
$65
G2Ind, Trade Course, Core Course, Spire-Approved Courses
The 1-PEU (.5 Trade/.5 Core) 2015 IMC Chapter 3 General Regulations Course will cover codes for General Listing and Labeling, Equipment and Appliance Location, Piping Support, Access and Service Space, and Condensate Disposal.
$65
G2Ind, Core Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, this 1-PEU course will cover Comfort, Food, Energy, and the Body, Heat Transfer, The Comfort Chart, Psychrometrics, Enthalpy, Humidity, Superheated Gases in Air, and Dry & Wet Bulb Temperatures.
$65
G2Ind, Core Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 1-PEU course will cover best practices for Pressure Valves, Piping, Electrical Hazards, Ladders, Heating/Cooling, Moving Heavy Objects, Mechanical Equipment, Refrigerants, and Chemicals.
$65
G2Ind, Core Course, 2-PEU
Taught by Chris Cordia and Louie Reinoso from American Trade School, the 2 Core PEU Soft Skills and Customer Service Course will cover topics ranging from Communication, Professionalism, and Customer Relations.
$125
G2Ind, Core Course, 1-PEU, Spire-Approved Courses
Taught by Chris Cordia from American Trade School, the 2-hour, 1-PEU Silica Dust Protection Course will cover the topic of Respirable Crystalline Silica in Construction Workplaces.
$65